JD-SPN1180-FMI0 serious John Deere PowerTech ›

Turbocharger #1 Turbine Inlet Temperature - Data Valid but Above Normal Operational Range (Most Severe)

The JD-SPN1180-FMI0 (John Deere PowerTech) diesel fault code means: Turbocharger #1 Turbine Inlet Temperature - Data Valid but Above Normal Operational Range (Most Severe). This is a serious severity code.

My Garage →
Keep driving?
Yes, with caution
DIY difficulty
advanced
Estimated cost
$450-$900 boost sensor, $2,200-$6,500 turbo R&R

What Are the Symptoms of JD-SPN1180-FMI0?

  • Loss of power / white or black smoke
  • VGT / wastegate not responding -- turbo surge
  • Engine-protection derate on over-boost

What Causes JD-SPN1180-FMI0? (Most Likely First)

  • VGT actuator sticking from soot / moisture inside housing Very Likely
  • Boost sensor feed line to CAC cracked / oiled up Likely
  • Turbo shaft wear causing bearing play Possible
  • Oil feed restriction to turbo bearings Less Likely

Can I Still Drive with JD-SPN1180-FMI0?

Yes, with caution. JD-SPN1180-FMI0 is rated serious severity. Keep trips short and get it diagnosed soon rather than waiting for symptoms to worsen.

Frequently Asked Questions

What is John Deere fault code SPN 1180 FMI 0?

On John Deere PowerTech engines, SPN 1180 FMI 0 means: Turbocharger #1 Turbine Inlet Temperature - Data Valid but Above Normal Operational Range (Most Severe). Serious code -- address promptly to avoid inducement / further damage.

Can I keep using my John Deere tractor with SPN 1180 FMI 0?

Serious fault -- you can move the machine to a shop but don't run it under load. Diagnose with John Deere Service ADVISOR via an EDL v3 / CF3 interface.

How much does it cost to fix John Deere SPN 1180 FMI 0?

Repair cost range: $450-$900 boost sensor, $2,200-$6,500 turbo R&R. Dealer labor on large tractors runs $180-$240/hr in 2026.

Mechanics Guide Step-by-step diagnosis

How Do You Diagnose JD-SPN1180-FMI0?

  1. Command VGT vanes full sweep in Service ADVISOR and verify smooth motion.

  2. Inspect CAC piping for blue oil film (bearing seep) and cracked hoses.

  3. Perform turbo shaft radial play check per CTM spec.

  4. Sample engine oil if soot is elevated -- consider oil change interval.

Sources 1

This page is built from documented references. Verify against your own service info before repair work.

  • SAE J1939-73Application Layer: Diagnostics (defines the SPN/FMI fault-identifier framework)

Which Vehicles Commonly Get JD-SPN1180-FMI0?

  • 2015+ John Deere 7R Series (7210R, 7250R, 7290R, 7310R)
  • 2015+ John Deere 8R / 8RT Series (8245R-8370R)
  • 2015+ John Deere 9R / 9RT / 9RX Series (9370R-9620R)
  • John Deere S670 / S680 / S690 combines
  • John Deere S770 / S780 / S790 combines
  • John Deere 544 / 624 / 724 wheel loaders
  • John Deere R4045 / R4060 self-propelled sprayers

Explore More

More John Deere PowerTech codes → Diesel home All diesel codes Heavy-duty Guides

Was this helpful?

Send this to whoever is fixing the truck — your tech, or the person asking what the fault means.