Right Rear Wheel Speed Sensor Circuit
The ISUZU-C1005 (Isuzu) diesel fault code means: Right Rear Wheel Speed Sensor Circuit. This is a moderate severity code.
- Keep driving?
- Short distances only
- DIY difficulty
- diy
- Estimated cost
- $180-$900
Down with a Isuzu fault on the road?
We are building a network of verified mobile diesel and reefer technicians along the freight corridor. It is not live yet — no one can be dispatched to you today. You can see where the pilot is launching and register interest.
View pilot availability →What Are the Symptoms of ISUZU-C1005?
- ABS warning lamp on
- Loss of ABS / stability assist
- Speedometer operates normally (unless driven off VSS)
- Possible traction control fault
- Limp-capable but not advisable for loaded deliveries
What Causes ISUZU-C1005? (Most Likely First)
- Wheel speed sensor tone-ring contaminated with brake dust / road debris Likely
- Broken or corroded WSS connector at knuckle / axle Likely
- Failed ABS module solenoid or relay (aging NPR / NQR) Possible
- Cracked tone ring on hub / axle from impact Possible
- Wiring chafed on inner fender liner Possible
Can I Still Drive with ISUZU-C1005?
Short distances only. ISUZU-C1005 is rated moderate severity. Keep trips short and get it diagnosed soon rather than waiting for symptoms to worsen.
Frequently Asked Questions
What does Isuzu code C1005 mean?
Isuzu diagnostic trouble code C1005 (Right Rear Wheel Speed Sensor Circuit) is a moderate-severity fault on Isuzu medium-duty diesel engines. It indicates a problem in the ABS / chassis that should be verified with a scan tool (Isuzu IDSS / Tech2 for Isuzu) before replacing any parts.
Can I drive my Isuzu truck with C1005?
Short runs may be possible but do not ignore — Isuzu medium-duty aftertreatment faults cascade quickly into 5-mph derate or no-restart. Schedule diagnosis immediately.
How much does it cost to fix Isuzu C1005?
Estimated repair cost runs $180-$900. Sensor, wiring, and DEF-related repairs fall at the low end; DPF service, turbo, injector, and EGR cooler work fall at the high end and may require dealer-level programming.
Mechanics Guide Step-by-step diagnosis
How Do You Diagnose ISUZU-C1005?
Connect IDSS or generic ABS scan tool and confirm C1005 active with freeze-frame wheel speeds.
Clean the reluctor ring and WSS face with brake cleaner — contaminated signal is often mistaken for a failed sensor.
Back-probe the WSS connector with key-on; should read ~1-2 VAC square wave as wheel is spun by hand.
Measure resistance across sensor — spec varies (900-2000 ohms depending on model); open or out of range means replace.
If sensors are good, check ABS module supply voltage and ground integrity at frame mount.
C1005 on Other Platforms
The same code ID appears across other engines, vehicles, and equipment. Diagnostic flow varies by platform — see the matching breakdown:
Which Vehicles Commonly Get ISUZU-C1005?
- Isuzu NPR / NPR-HD with 4HK1 5.2L
- Isuzu NPR-XD / NQR with 4HK1 5.2L
- Isuzu NRR with 4HK1 / 6HK1
- Isuzu FTR / FVR medium-duty with 6HK1 7.8L
- Chevrolet / GMC 4500 / 5500 (Isuzu-chassis) with 4HK1
- Isuzu NPR-ECO-MAX with 3.0L 4JJ1
Explore More
Was this helpful?
Send this to whoever is fixing the truck — your tech, or the person asking what the fault means.