FPT Cursor Engine Oil Pressure Too Low (Severe)
The FPT-SPN100-FMI1 (FPT Cursor (Case IH / New Holland)) diesel fault code means: FPT Cursor Engine Oil Pressure Too Low (Severe). This is a critical severity code.
- Keep driving?
- No — stop driving
- DIY difficulty
- intermediate
- Estimated cost
- $30-$120 oil+filter, $180-$450 sensor, $3K+ bottom end
A $30 car code reader can't do diesel. The HD7000 reads full-system codes and does parked DPF regen, idle/speed-limit, and service resets from the cab — on everything from a 6.7 Cummins/Power Stroke/Duramax pickup to Class-8 trucks (Detroit, Paccar, CAT, Volvo, Mack, International).
Full-system 6/9/16-pin diesel scan tool for Cummins, Paccar, CAT, Detroit and more — plug-and-play, no subscription. A cheaper way to read heavy-duty codes a basic OBD2 scanner skips entirely.
Affiliate links — we earn a commission at no extra cost to you.
What Are the Symptoms of FPT-SPN100-FMI1?
- Shutdown / derate
- Red stop lamp
What Causes FPT-SPN100-FMI1? (Most Likely First)
- Low oil level / wrong oil Very Likely
- Failed oil pressure sensor Likely
- Worn oil pump Possible
Can I Still Drive with FPT-SPN100-FMI1?
No — stop driving. FPT-SPN100-FMI1 is rated critical severity. Continuing to drive in this state risks further damage — get it looked at before your next trip.
Frequently Asked Questions
What is Case IH / New Holland SPN 100 FMI 1?
On FPT Cursor engines, SPN 100 FMI 1 means: FPT Cursor Engine Oil Pressure Too Low (Severe). Critical code -- stop operating until repaired.
Can I keep operating with SPN 100 FMI 1?
Critical fault -- do not operate; tow or trailer to a dealer. Diagnose with Case IH EST / New Holland Electronic Service Tool.
How much does SPN 100 FMI 1 cost to fix?
Repair cost range: $30-$120 oil+filter, $180-$450 sensor, $3K+ bottom end.
Mechanics Guide Step-by-step diagnosis
How Do You Diagnose FPT-SPN100-FMI1?
Confirm with mechanical gauge at test port.
Check oil spec CK-4 SAE 15W-40 (or 10W-40 for extended drain intervals).
Sources 3
This page is built from documented references. Verify against your own service info before repair work.
- John Deere Operator's Manual, PowerTech 4.5 L and 6.8 L Tier 2 OEM Diesel Engines, OMRG33324 (Issue 16Feb04), reproduced as a supplement in Genie's telehandler parts library (doc 237949), "Listing of Diagnostic Trouble Codes"printed page 45-24: SPN 100 FMI 01, "Engine Oil Pressure Extremely Low". The table is that engine maker's; it establishes what the J1939 SPN-FMI pair means, not that a Case IH / New Holland display shows it.
- Perkins 404F-22 Engine Fault Codes table, printed in the Genie S-40/S-45 Service Manual, Part No. 826364, February 2014printed page 5-25: SPN 100 FMI 1, "Engine Oil Pressure: Low - most severe (3)". The table is that engine maker's; it establishes what the J1939 SPN-FMI pair means, not that a Case IH / New Holland display shows it.
- Deutz TCD 2.2 L3 Engine Fault Codes table, printed in the Genie SX-135 XC Service and Repair Manual, Part No. 1263383GT, April 2023printed page 158: SPN 100 FMI 1 (DTCs 1025/1026), "Low oil pressure. Warning threshold exceeded" and "Low oil pressure. Shut off threshold exceeded". The table is that engine maker's; it establishes what the J1939 SPN-FMI pair means, not that a Case IH / New Holland display shows it.
SPN100-FMI1 on Other Platforms
The same code ID appears across other engines, vehicles, and equipment. Diagnostic flow varies by platform — see the matching breakdown:
Which Vehicles Commonly Get FPT-SPN100-FMI1?
- Case IH Magnum 250-400 Series tractors
- Case IH Steiger 370-620 articulated tractors
- Case IH Axial-Flow 7250 / 8250 / 9250 combines
- New Holland T8 / T9 Series tractors
- New Holland CR Series combines (CR8.90, CR9.90, CR10.90)
Explore More
Was this helpful?
Send this to whoever is fixing the truck — your tech, or the person asking what the fault means.