CAT-SPN110-FMI0 critical Caterpillar ›

Engine Coolant Temperature Above Normal

The CAT-SPN110-FMI0 (Caterpillar) diesel fault code means: Engine Coolant Temperature Above Normal. This is a critical severity code.

My Garage →
Keep driving?
No — stop driving
DIY difficulty
advanced
Estimated cost
$500-$5000
Mobile mechanic network · I-5 corridor pilot

Down with a CAT fault on the road?

We are building a network of verified mobile diesel and reefer technicians along the freight corridor. It is not live yet — no one can be dispatched to you today. You can see where the pilot is launching and register interest.

View pilot availability →

What Are the Symptoms of CAT-SPN110-FMI0?

  • Check Engine Light or warning lamp
  • Engine protect / derate / shutdown possible
  • System performance affected

What Causes CAT-SPN110-FMI0? (Most Likely First)

  • Sensor / actuator internal failure Likely
  • Wiring or connector issue in the affected circuit Likely
  • Related system mechanical issue Possible
  • ECM calibration or software issue Less Likely

Can I Still Drive with CAT-SPN110-FMI0?

No — stop driving. CAT-SPN110-FMI0 is rated critical severity. Continuing to drive in this state risks further damage — get it looked at before your next trip.

Frequently Asked Questions

What does CAT SPN110-FMI0 mean?

CAT SPN110-FMI0 (Engine Coolant Temperature Above Normal) is a critical-severity fault reported over the J1939 data link. Coolant too hot — engine protect / derate. CAT ECMs report many of the same faults both as CID/FMI (proprietary) and SPN/FMI (J1939) — either form points to the same physical issue.

Can I drive with CAT SPN110-FMI0?

No — protect the engine and diagnose before operating.

How much does CAT SPN110-FMI0 cost to fix?

Typical repair is $500-$5000. Simple sensor/wiring repairs fall at the low end; component, actuator, or aftertreatment work falls at the high end and usually requires CAT ET for programming.

Mechanics Guide Step-by-step diagnosis

How Do You Diagnose CAT-SPN110-FMI0?

  1. Connect CAT ET and confirm the SPN/FMI is active; record live data for the affected parameter.

  2. Inspect wiring and connectors for the affected circuit; back-probe and check with a DMM.

  3. Perform component test on the sensor / actuator per CAT service manual.

  4. Repair wiring, replace component, or reflash ECM as CAT ET diagnostics direct.

Sources 1

This page is built from documented references. Verify against your own service info before repair work.

  • SAE J1939-73Application Layer: Diagnostics (defines the SPN/FMI fault-identifier framework)

Which Vehicles Commonly Get CAT-SPN110-FMI0?

  • Kenworth T800 with CAT C15
  • Kenworth W900 with CAT C15
  • Kenworth T2000 with CAT C15
  • Peterbilt 379 with CAT C15
  • Peterbilt 389 with CAT C15
  • Peterbilt 386 with CAT C15
  • Peterbilt 387 with CAT C15
  • Freightliner Classic XL with CAT C15
  • International 9200i with CAT C15
  • International 9400i with CAT C15
  • Western Star 4900 with CAT C15
  • Western Star 5900 with CAT C15
  • Kenworth T800 with CAT C13
  • Kenworth T660 with CAT C13
  • Peterbilt 386 with CAT C13
  • Peterbilt 387 with CAT C13
  • Freightliner Columbia with CAT C13
  • International 9200i with CAT C13

Explore More

More Caterpillar codes → Diesel home All diesel codes Heavy-duty Guides

Was this helpful?

Send this to whoever is fixing the truck — your tech, or the person asking what the fault means.